

| パラメータ | 価値 |
|---|---|
| max. 10 s (Boot time) | |
| 注記 | G3 |
| 深さ | 113.6 mm |
| ショック | 10g for Δt = 16 ms (continuous shock, 1000 shocks in each space direction) |
| 幅 | 22.61 mm |
| 身長 | 107.74 mm |
| 現在 | max. 30 mA (Sensor current recording per channel) |
| 頻度 | 20 Hz (max. recommended sensor signal frequency, as current input) |
| 精度 | typ. ± 2 % (as current input, relative to the measuring range final value) |
| プラグイン可能 | yes |
| 名前を入力 | IN S1, IN S2, IN S3, IN S4 |
| インターフェース | DIN rail TBUS for connection to the master module, supplied as standard |
| 応用 | Analog IN |
| 説明 | Sensor supply voltage per analog input |
| 指定 | A1/A2 |
| フィルター時間 | typ. 5 ms (in the event of voltage dips at Us) |
| 製品タイプ | Safety device |
| 再起動時間 | min. 5 s (Boot time) |
| 取り付けタイプ | DIN rail mounting |
| 応答時間 | see user manual |
| スキャン速度 | 2.5/5/10/16.6/20/50/60/100/200/400/800/1000/2000/4000 Hz |
| 停止カテゴリ | 0 |
| 識別 | CE-compliant |
| 突入電流 | max. 14 A (Δt = 1 ms at Us) |
| ステータス表示 | 4x LED (yellow, red) |
| 供給電圧 | 24 V DC ±3 % |
| ハウジング材質 | Polyamide PA non-reinforced |
| 最大高度 | ≤ 2000 m (Above sea level) |
| 入力数 | 4 |
| 保護クラス | III |
| 剥ぎ取り長さ | 10 mm |
| 接続方法 | Push-in connection |
| 取り付け位置 | vertical or horizontal |
| 保護回路 | Serial protection against polarity reversal |
| 許容電圧 | max. 24 V (as current input) |
| 短絡防止 | yes |
| 現在の入力信号 | 0 mA ... 25 mA (Measuring range) |
| 保護の程度 | IP20 |
| 解像度(現在) | 381 nA |
| 解像度(電圧) | 152 µV |
| 電圧入力信号 | 0 V ... 12 V (Measuring range) |
| 組み立て説明書 | Observe derating |
| 接続技術 | 2-conductor, 3-conductor or 4-conductor (2-conductor sensor signal + 2-conductor sensor supply) |
| 振動(操作) | 10 Hz ... 150 Hz, 2g |
| 限界周波数(3 dB) | 160 Hz (RC low pass, 1st order, as current input) |
| 公称動作モード | 100% operating factor |
| パフォーマンスレベル(PL) | e (2-channel wiring) |
| 米国の電力消費量 | typ. 1.96 W (without sensor supply) |
| A/Dコンバータの解像度 | 16 bit |
| 入力の説明 | Safety-oriented analog inputs, configurable as current or voltage inputs, galvanically isolated |
| 最大許容電流 | max. 35 mA (as current input) |
| 許容ケーブル長 | max. 100 m (per input) |
| 定格絶縁電圧 | 250 V AC |
| 温度係数 | typ. ± 0.07 %/K |
| 動作電圧表示 | 1 x green LED |
| 導体断面積AWG | 24 ... 16 |
| 安全度水準(SIL) | 3 |
| 導体断面積は剛性 | 0.2 mm² ... 2.5 mm² |
| 入力抵抗電流入力 | 290 Ω ±25 % (incl. internal protective circuit) |
| 定格サージ電圧/絶縁 | Basic insulation 4 kV between all current paths and housing |
| 周囲温度(動作) | -10 °C ... 70 °C (observe derating) |
| 定格制御電源電流 IS | typ. 82 mA (without sensor supply) |
| 導体断面積が柔軟 | 0.2 mm² ... 2.5 mm² |
| 電圧入力の入力抵抗 | 185 kΩ ±25 % |
| 周囲温度(保管/輸送) | -20 °C ... 85 °C |
| 定格制御回路電源電圧(米国) | 19.2 V DC ... 28.8 V DC |
| 接続技術に関する注意事項 | shielded |
| 設備設置場所の最小保護等級 | IP54 |
| 最大許容湿度(保管/輸送) | 95 % (non-condensing) |
| 最大許容相対湿度(動作) | 95 % (non-condensing) |
| 公称条件での最大消費電力 | 2.76 W (with max. permissible load) |
技術仕様と性能データ
設置・操作ガイド