

| パラメータ | 価値 |
|---|---|
| 120 V DC | |
| 導かれた | no |
| 幅 | 54 mm |
| コーディング | A |
| 身長 | 42 mm |
| 長さ | 117 mm |
| 一般的な | When connecting the signal lines to the black PCB terminal blocks, please use a 0.4 x 2.0 mm screwdriver.The black PCB terminal blocks only require a minimal amount of operating force.Screwdriver: SZS 0,4X2,0 - 1205202Using larger screwdrivers or excessive force may damage the PCB terminal blocks.When using ferrules, the wires can be inserted straight into the PCB terminal blocks without opening the clamping area. |
| 応用 | Standard |
| 製品タイプ | Distributor box |
| 組み立てノート | NOTE:Observe the permissible bending radii when routing cables, since the degree of protection may be at risk if the bending forces are too high. Reduce mechanical loads upstream of the connector, e.g., by using cable ties. |
| スロット数 | 4 |
| 接触材料 | Cu alloy |
| マテリアルハウジング | PBT |
| 接続方法 | Spring-cage connection |
| 公称電圧UN | 120 V AC |
| 寸法図 | |
| 申請に関する注意事項 | Unused slots are to be sealed off prior to commissioning. Suitable sealing elements are to be found under "Accessories". |
| ポジション数 | 5 |
| 保護の程度 | IP65 |
| 定格電流、合計 | 12 A |
| シール材Oリング | NBR |
| 標準指定 | M12 connector |
| ステータス表示あり | No |
| ケーブル外径 | 7 mm ... 12 mm |
| 接触キャリア材料 | PA |
| 接触面材質 | gold-plated |
| 材質 ねじ付きスリーブ | PBT |
| 規格/仕様 | IEC 61076-2-101 |
| 材料 成形コンパウンド | PUR |
| 剥き長さ 信号線 | 6 mm |
| 締め付けトルク、ユニオンナット | 2.5 Nm |
| ストリップ長さ 電源 | 10 mm |
| シースの剥ぎ取り長さ | 50 mm (Master cable) |
| 締め付けトルク、カバーネジ | 1 Nm |
| 周囲温度(動作) | -25 °C ... 80 °C |
| センサー/アクチュエータ接続システム | M12-SPEEDCON-socket |
| スロットあたりの電流容量 | 4 A |
| UL 94準拠の難燃性評価 | V0 |
| パスあたりの最大電流容量 | 2 A |
| スロット/位置 = 配線の色または接続 | 1 / 4 (A) = WH |
| 導体断面積フレキシブル信号線 | 0.2 mm² ... 0.5 mm² |
| 締め付けトルクスロットセンサー/アクチュエータケーブル | 0.4 Nm |
| 導体断面積フレキシブル電源 | 0.2 mm² ... 1.5 mm² |
| 接続断面積 AWG フレキシブル信号線 | 24 ... 20 |
| 接続断面積AWGフレキシブル電源 | 24 ... 16 |
| ハウジング固定用取付ネジの締め付けトルク | 0.5 Nm |
技術仕様と性能データ
設置・操作ガイド