在庫あり 注目商品
UHLAC1P
UHLAC1P HLAC1P HL-AC1P PANASONIC HL-T1 sensor controller PNP, 12-24VDC
$0.00米ドル
4344 在庫あり
主な仕様
アイテム:Specifications
タイプ:PNP output
重さ:Net weight: 140 g approx.
詳細:Controller (PNP output)
サプライヤー情報
PANASONIC
製品: 4316
通常、2〜3営業日以内に出荷します
品質保証済み
高速配送
テクニカルサポート
技術仕様
| パラメータ | 価値 |
|---|---|
| アイテム | Specifications |
| タイプ | PNP output |
| 重さ | Net weight: 140 g approx. |
| 詳細 | Controller (PNP output) |
| 製品 | Ultra-compact Laser Collimated Beam Sensor |
| 材料 | Enclosure: Polybutylene terephthalateTransparent cover: Polycarbonate |
| I/Oケーブル | 0.09 mm210-core composite cable, 2 m6.562 ftlong |
| 部品番号 | HL-AC1P |
| 入力をリセット | +V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| 製品名 | Ultra-compact Laser Collimated Beam Sensor HL-T1 |
| タイミング入力 | +V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| リニア出力 | Current / voltage output switchable (Note)-During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm-During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm(In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.)(Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller. |
| 主な機能 | ・Measured value display・Setting value, light amount value resolution display・Standard received light setting・Automatic scaling・Scaling・Display reverse・ECO display・Display digits limitation・Sample hold・Peak hold・Bottom hold・Peak to peak hold・Self peak hold・Self bottom hold・Zero reset・Initial reset・ON-delay timer・OFF-delay timer・One-shot timer・Differentiation・Sensitivity selection・Threshold value direct setting・Positioning teaching・2-point teaching・Automatic teaching・Hysteresis width variability・Monitor focus・Non-measuring time setting・(A – B) calculation(Note：The calculation unit is necessary.)・(A + B) calculation(Note：The calculation unit is necessary.)・Mutual interference prevention (Note：The calculation unit is necessary.)・Laser deterioration detection・Key lock・Zero reset memory |
| 製品番号 | HL-AC1P |
| 供給電圧 | 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less |
| レーザーOFF入力 | +V connection: Laser emission haltOpen: Laser emission-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| 測定サイクル | 150 micro s |
| 汚染度 | 3 (industrial environment) |
| ゼロリセット入力 | +V connection: Zero reset operatesOpen: Zero reset ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| 消費電流 | 190 mA or less (when connected to the sensor head) |
| I/Oケーブル延長 | Extension up to total 10 m32.808 ftis possible, with 0.09 mm2or more, cable.(Note) If the extension cable is longer than 10 m32.808 ft, then it will not qualify for CE marking. |
| サブデジタルディスプレイ | 5 digit yellow LED display[RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.] |
| メインデジタルディスプレイ | 5 digit red LED display[RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.] |
| 絶縁抵抗 | 20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure |
| 適用センサーヘッド | HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F |
| 耐電圧性 | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
| インジケーター: 有効 (ENABLE) | Green LED (lights up during normal operation) |
| 指標：判断出力 | HIGH: Orange LED (lights up when measured value > HIGH threshold value)PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value)LOW: Yellow LED (lights up when LOW threshold value > measured value) |
| インジケーター：ゼロリセット（ZERO） | Green LED (lights up when the zero reset function is enabled) |
| 設定可能な平均サンプリングレート | 1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096(Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1). |
| CEマーキング指令への準拠 | EMC Directive, RoHS Directive |
| 判定出力（HIGH、PASS、LOW） | PNP open-collector transistor-Maximum source current: 50 mA-Applied voltage: 30 V DC or less (between judgment output and +V)-Residual voltage: 2 V or less (at 50 mA source current) |
| インジケーター：レーザー発光（LD ON） | Green LED (lights up during laser emission) |
| 耐環境性：周囲湿度 | 35 to 85 % RH, Storage: 35 to 85 % RH |
| 耐環境性：耐衝撃性 | 300 m/s2acceleration (30 G approx.) in X, Y and Z directions three times each |
| リニア出力：温度特性 | plus or minus 0.2 % F.S./℃(Note) These are the temperature characteristics of the linear output when the sensor head is connected. |
| 耐環境性：周囲温度 | 0 to +50 ℃+32 to +122 ℉(No dew condensation allowed), Storage: -25 to +65 ℃-13 to +149 ℉ |
| 耐環境性：耐振動性 | 10 to 150 Hz frequency, 0.7 mm0.028 indouble amplitude in X, Y and Z directions for 80 min. |
| 判定出力（HIGH、PASS、LOW）:出力動作 | HIGH: ON when measured value > HIGH threshold valuePASS: ON when HIGH threshold value >= measured value >= LOW threshold valueLOW: ON when LOW threshold value > measured value |
| 判定出力（HIGH、PASS、LOW）: 出力数 | HIGH / PASS / LOW 3 values output |
| 判定出力（HIGH、PASS、LOW）：利用カテゴリー | DC-12 or DC-13 |
| 判定出力（HIGH、PASS、LOW）：短絡保護 | Incorporated |
製品説明
HLT1 series controller, 12-24 VDC power, PNP digital output, selectable analog output between 4-20mA and ±4V
主な機能
- 産業グレードの品質
- RoHS準拠
- CE認証取得
- 1年保証
製品資料
データシート
技術仕様と性能データ
ユーザーマニュアル
設置・操作ガイド
