在庫あり 注目商品
HC-HS 2-D7-EBUS
HC-HS 2-D7-EBUS 1586264 PHOENIX CONTACT Contact insert
$35.46米ドル
326 在庫あり
主な仕様
:Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
タイプ:D7
テスト:DIN VDE 0627/86
幅:21 mm
サプライヤー情報
製品: 0
通常、2〜3営業日以内に出荷します
品質保証済み
高速配送
テクニカルサポート
技術仕様
| パラメータ | 価値 |
|---|---|
| Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque. | |
| タイプ | D7 |
| テスト | DIN VDE 0627/86 |
| 幅 | 21 mm |
| 身長 | 34.8 mm |
| 長さ | 21 mm |
| シリーズ | HC-HS |
| 一般的な | for HC-D7 housing, axial connection 2.0 mm, Allen key |
| 応用 | Power |
| 製品タイプ | Contact insert with a fixed no. of positions |
| 組み立てノート | To ensure correct use, installation in housing with IP54 protection or better is required |
| 定格電流 | 40 A |
| 記事の改訂 | 04 |
| 接触直径 | 4 mm |
| 接触材料 | Copper alloy |
| 六角ソケット | SW2,0 |
| 連絡先番号 | 1 - 2 |
| 締め付けトルク | 0.5 Nm ... 0.8 Nm (Mounting screws for mounting in the HEAVYCON housing) |
| 接続プロファイル | 2+PE |
| 汚染度 | 3 |
| 寸法図 | |
| ポジション数 | 2 |
| 定格サージ電圧 | 6 kV |
| 過電圧カテゴリー | III |
| 接続技術 | Axial screw connection |
| 接触材料の種類 | turned |
| 電源接点数 | 2 |
| 定格電圧（III/3） | 400 V |
| 導体断面積 | 4 mm² ... 10 mm² (The cross section specification refers to the geometric cross section of the cable used) |
| 接触キャリア材料 | PC |
| 接触面材質 | Ag |
| 挿入/離脱サイクル | ≥ 500 |
| 接続断面積AWG | 10 ... 8 |
| 周囲温度（動作） | -40 °C ... 125 °C (including heating up of contacts) |
| 標準に準拠した接続 | IEC / EN |
| 構造および試験規制 | DIN VDE 0627/86 |
| UL 94準拠の難燃性評価 | V0 |
| 個々の電線の被覆剥き長さ | 8 mm +1 mm |
製品説明
Contact insert, number of poles: 2+PE, size: D7, power contacts: 2, Female, Axial screw connection, 400 V, 40 A, 4 mm² ... 10 mm², Application: Power
主な機能
- 産業グレードの品質
- RoHS準拠
- CE認証取得
- 1年保証
製品資料
データシート
技術仕様と性能データ
ユーザーマニュアル
設置・操作ガイド
